Masters Theses in the Pure and Applied Sciences

Masters Theses in the Pure and Applied Sciences
Author: Wade H. Shafer
Publisher: Springer Science & Business Media
Total Pages: 314
Release: 2012-12-06
Genre: Science
ISBN: 1468449192

Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1 957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 28 (thesis year 1 983) a total of 10,661 theses titles from 26 Canadian and 197 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 28 reports theses submitted in-1983, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.

Aeronautical Engineering

Aeronautical Engineering
Author:
Publisher:
Total Pages: 856
Release: 1977
Genre: Aeronautics
ISBN:

A selection of annotated references to unclassified reports and journal articles that were introduced into the NASA scientific and technical information system and announced in Scientific and technical aerospace reports (STAR) and International aerospace abstracts (IAA).

Evaluation of Boattail Geometry and Exhaust Plume Temperature Effects on Nozzle Afterbody Drag at Transonic Mach Numbers

Evaluation of Boattail Geometry and Exhaust Plume Temperature Effects on Nozzle Afterbody Drag at Transonic Mach Numbers
Author: L. L. Galigher
Publisher:
Total Pages: 144
Release: 1976
Genre: Aerodynamics, Transonic
ISBN:

An experimental program was conducted to investigate the interaction effects which occur between the nozzle exhaust flow and the external flow field associated with isolated nozzle afterbody configurations at transonic Mach numbers. Pressure data were obtained from three afterbody geometries with boattail angles of 10, 15, and 25 deg at Mach numbers from 0.6 to 1.5 at zero angles of attack and sideslip. Cold (High-pressure air) and hot (Air/ethylene combustion) jet test techniques were used to simulate and duplicate, respectively, the nozzle exhaust flow for a sonic jet installation. Nozzle exhaust temperature was varied from 540 to approximately 2,900 R. The most significant results pertain to those effects on boattail pressure drag caused by exhaust plume temperature and flow asymmetry (Model support strut induced). The differences obtained in boattail pressure drag between the cold jet simulation and hot jet duplication results were significant at nozzle pressure ratios representative for turbofan and turbojet engines at subsonic Mach numbers. Adjusting the cold jet nozzle pressure ratio to correct for changes in the exhaust plume specific heat ratio with temperature did not account for the differences observed. Flow asymmetry effects were Mach number and nozzle pressure ratio dependent and increased in severity as the boattail angle was increased.

Experimental Method for Correcting Nozzle Afterbody Drag for the Effects of Jet Temperature

Experimental Method for Correcting Nozzle Afterbody Drag for the Effects of Jet Temperature
Author: W. L. Peters
Publisher:
Total Pages: 50
Release: 1981
Genre: Airplanes
ISBN:

The objective of this investigation was to isolate those parameters defined as jet mixing effects on afterbody drag in an effort to develop a method of correcting or simulating the effects of jet temperature in wind tunnel experiments. Data used in the investigation were obtained from experiments conducted in the AEDC Aerodynamic Wind Tunnel (1T) with a strut-mounted model at free-stream Mach numbers from 0.6 to 1.2. Integrated afterbody pressure drag coefficient data were acquired for three nozzle area ratios (1.0, 1.24, and 2.96) using various unheated jet exhaust gas compositions that allowed a variation in gas constant from 55 to 767 ft/lbf/lbm-deg R. Jet mixing effects on afterbody drag coefficient produced by varying jet gas constant and nozzle area ratio at nozzle design pressure ratio, and the drag effects resulting from variations in nozzle pressure ratio at certain overexpanded jet conditions were observed to be similar functions of mass flux ratio. A simple experimental method has been proposed to allow corrections of afterbody drag coefficient data obtained in the wind tunnel (using an ambient temperature air jet) for the effects of jet gas constant. By inference, a similar drag correction can be obtained for the combined effect of gas constant and temperature, assuming their product defines the effects on drag produced by variations in either property. (Author).

A Method for Estimating Jet Entrainment Effects on Nozzle-afterbody Drag

A Method for Estimating Jet Entrainment Effects on Nozzle-afterbody Drag
Author: R. C. Bauer
Publisher:
Total Pages: 30
Release: 1980
Genre: Airplanes
ISBN:

A highly simplified analysis was used to derive an expression for estimating the induced afterbody drag caused by the turbulent jet-mixing process. The approach estimates the induced velocity produced by the jet-mixing process and uses small perturbation concepts to estimate the resulting pressure change on the afterbody surface from which the induced afterbody drag coefficient is obtained. The theoretical induced afterbody drag (entrainment drag) is combined with the maximum jet plume diameter blockage condition to form a correlation method that accounts for the effect of jet area ratio, exit angle, total temperature, molecular weight and ratio of specific heats for a given external stream Mach number, Reynolds number, and afterbody geometry. For verification, the correlation method was used to predict the drag of an H2 and C2H4 jet from the measured drag of an N2 jet and to predict the drag of a hot jet from the measured drag of a cold jet for both the 15- and 25-deg AGARD afterbody configurations in the Mach number range from 0.6 to 1.5. The average accuracy of the correlation method is better than 10% for both afterbody configurations and is 40 to 50 % more accurate than a correlation method based only on the blockage parameter. A brief numerical study indicates that the major parameter which correlates the jet entrainment effect is the product of the jet gas constant and total temperature. (Author).

Scientific and Technical Aerospace Reports

Scientific and Technical Aerospace Reports
Author:
Publisher:
Total Pages: 456
Release: 1995
Genre: Aeronautics
ISBN:

Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.

High-speed Wind Tunnels

High-speed Wind Tunnels
Author: Luigi Crocco
Publisher:
Total Pages: 236
Release: 1946
Genre: Aerodynamics, Supersonic
ISBN:

The importance assumed in recent times by experimental supersonic wind tunnels, as well as the power required, has brought about the need for a study which would permit a comparison of the types tested and the principal theoretical plans.