Masters Theses in the Pure and Applied Sciences

Masters Theses in the Pure and Applied Sciences
Author: W. H. Shafer
Publisher: Springer Science & Business Media
Total Pages: 319
Release: 2012-12-06
Genre: Science
ISBN: 1468433814

Masters Theses in the Pure and Applied Sciences was first conceived, published, and dis seminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the ac tivity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all concerned if the printing and distribution of the volume were handled by an international publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Corporation of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 22 (thesis year 1977) a total of 10,658 theses titles from 28 Canadian and 227 United States universities. We are sure that this broader base for theses titles reported will greatly enhance the value of this important annual reference work. While Volume 22 reports theses submitted in 1977, on occasion, certain universities do report theses submitted in previous years but not reported at the time.

NASA SP-7500

NASA SP-7500
Author: United States. National Aeronautics and Space Administration
Publisher:
Total Pages: 814
Release: 1982
Genre:
ISBN:

Project Management with Dynamic Scheduling

Project Management with Dynamic Scheduling
Author: Mario Vanhoucke
Publisher: Springer Science & Business Media
Total Pages: 321
Release: 2013-11-29
Genre: Business & Economics
ISBN: 3642404383

The topic of this book is known as dynamic scheduling, and is used to refer to three dimensions of project management and scheduling: the construction of a baseline schedule and the analysis of a project schedule’s risk as preparation of the project control phase during project progress. This dynamic scheduling point of view implicitly assumes that the usability of a project’s baseline schedule is rather limited and only acts as a point of reference in the project life cycle. Consequently, a project schedule should especially be considered as nothing more than a predictive model that can be used for resource efficiency calculations, time and cost risk analyses, project tracking and performance measurement, and so on. In this book, the three dimensions of dynamic scheduling are highlighted in detail and are based on and inspired by a combination of academic research studies at Ghent University (www.ugent.be), in-company trainings at Vlerick Business School (www.vlerick.com) and consultancy projects at OR-AS (www.or-as.be). First, the construction of a project baseline schedule is a central theme throughout the various chapters of the book, and is discussed from a complexity point of view with and without the presence of project resources. Second, the creation of an awareness of the weak parts in a baseline schedule is discussed at the end of the two baseline scheduling parts as schedule risk analysis techniques that can be applied on top of the baseline schedule. Third, the baseline schedule and its risk analyses can be used as guidelines during the project control step where actual deviations can be corrected within the margins of the project’s time and cost reserves. The second edition of this book has seen corrections, additions and amendments in detail throughout the book. Moreover Chapter 15 on "Dynamic Scheduling with ProTrack" has been completely rewritten and extended with a section on "ProTrack as a research tool".

Project Management in Construction

Project Management in Construction
Author: Dennis Lock
Publisher: CRC Press
Total Pages: 209
Release: 2016-04-08
Genre: Business & Economics
ISBN: 1317075102

The one thing that all well-run, profitable construction projects have in common is that they benefit from good project managers. People who have the skills to plan the project, manage it and keep it on track whenever tight timescales, costs, people or other difficulties threaten to derail it. The good news is that there is no secret art to project management. These are the skills that any manager can learn and use. Project Management in Construction is a practical, easy-to-read guide to defining, organizing, planning, and executing a construction project so that it is completed to the satisfaction of the principal stakeholders. The book is part of the Leading Construction Series co-published by Gower and CITB-ConstructionSkills. The Leading Construction Series is part of a CITB-ConstructionSkills initiative to develop management skills within the industry. The books in this series are designed to be essentially practical, with a firm grounding in the construction industry.

Management

Management
Author:
Publisher:
Total Pages: 784
Release: 1968
Genre: Industrial engineering
ISBN: